設備及管道支座、吊架及法蘭、閥門、人孔等部位，在整體保溫時，預留一定裝卸間隙，待整體保溫及保護層施工完畢后，再做部分保溫處理。并注意施工完畢的保溫結構不得妨礙活動支架的滑動。保溫棉氈、墊的保溫厚度和密度應均勻，外形應規整，經壓實捆扎后的容重必須符合設計規定的安裝容重。

⑶保溫制品的拼縫寬度,一般不得大于5mm,且施工時需注意錯縫。保溫鉤釘銷釘的安裝，一般設備出廠前都已把保溫鉤釘和支承件焊接在設備上，到現場只要安裝保溫層和保護層就可以了。出廠前沒有焊好鉤釘需現場焊接的，單位面積上鉤釘或銷釘數，側部不應少于6個/m2

，底部不應少于8個/m2。焊接鉤釘或銷釘時，應先用粉線在設備、管道壁上錯行或對行劃出每個鉤釘或銷釘的位置。支承件的安裝，對于支承件的材質，應根據設備或管道材質確定，宜采用普通碳鋼板或型鋼制作。支承件不得設在有附件的位置上，環面應水平設置，各托架筋板之間安裝誤差應大于10mm，當不允許直接焊于設備上時，應采用抱箍型支承件，支承件制作的寬度應小于保溫層厚度10mm，但不得大于20mm，立式設備和公稱直徑大于100mm的垂直管道支承件的安裝間距，應視保溫材料松散程度而定。