石油管道設備罐體做保溫應注意什么做管道罐體設備的白鐵、鋁板、不銹鋼和不銹鐵、白鐵安裝外皮防護工程的安裝及設計。可承接各種鐵皮保溫工程、管道保溫工程、設備罐體保溫工程、高溫爐體保溫。保溫材料為硅酸鹽海泡石復合保溫材料、巖棉、玻璃棉、硅酸鋁、橡塑、聚氨酯等各種保溫材料。工程施工方便、以優惠的價格滿足廣大用戶的要求主要經營：建筑、電廠、制藥 ，環保 ，石油，化工，冶金等行業．設備，管道的。1、高溫保溫：這種保溫工程一般采用巖棉、玻璃棉、復合硅酸鹽等纖維類的保溫材料，考慮到高溫環境，所以保溫材料要具有耐高溫的特性。
2、低溫保溫：這類保溫工程使用聚氨酯等閉孔類保溫材料，不僅保溫效果好，而且吸水。
內層采用不同的材料，外層材料就要起到保護的作用，比如鐵皮、鋁皮、玻璃鋼等。
罐體保溫施工方法：罐體保溫工程層厚度層使用50-150mm的大型擺錘工藝巖棉、玻璃棉、硅酸鋁、復合硅酸鹽等保溫材料，特殊要求分兩層錯縫固定。外護層使用厚度為0.3-0.6mm的鍍鋅鐵皮、鋁皮、彩鋼板通過保溫的凹凸槽式壓邊機壓邊成型和防滑式滾圓機滾圓成筒進行搭接順水流方向，寬度適宜，接口平整，均勻的包裹。
罐體保溫施工特點：具有保溫效果好、工程造價低、施工周期短、外觀美觀、防水、防火、防腐等使用年限長達30-50年的優點。
設備保溫施工質量標準：
1.保溫層的質量檢查應符合下列規定
a. 保溫層完工后。用探針在每5㎡內各測一點，其厚度允許偏差-5%～10%；
b. 保溫層的捆扎間距和松緊程度符合本標準的規定。
保護層的質量檢查應符合下列規定：a. 表面為圓柱面的保護層要求規整、圓度圓滑、美觀。其平整度應用1m直尺沿軸向進行檢查，并用弦長300mm的弧形樣板沿環向檢查，空隙應不大于4mm（金屬保護層）或5mm（抹面保護層）；
c. 金屬保護層不得有